Controls / Products / Tepe Betopan

Controls®

Experience more than 35 years…

Composite building board that combine superior features of cement and wood.

Controls is a functional cement bonded particle board with flat and natural grey surface which can be used for buildings from base to roof..

Advantages of Use

Offers different architectural and constructive solutions by scene and structural characteristics from base to roof in buildings.
Highly preferred building board by superior functional features for especially prefabricated and steel buildings.
High impact resistance compared to gypsum based boards.
Can be used as a finishing material by painting, coating, wall papers.
Using as a backer board of int./ext. cladding materials.
Using as a sheathing board on floors and roofs.
Using with floor heating system
Using as a backer board behind tiles on wet spaces.
Easy to install and modification.
Easy to cut and drill
light weight and easy to carry
Protect the building from different weather conditions.
Provides for heat and acoustic insulations.
Resistant to seasonal changes.
Resistant to effect of sunlight.
Resistant to moisture and water.
Resistant to impact.
Resistant to biological and chemical wastes of animals.
Environment friendly, asbestos free.
Odourless and does not release toxic gas.
Insect-proof, non putrescible, no moulding.

Areas of Application

Interior

Internal walls
Floor / Raised floor
Mezzanine floor
Indoor ceilings
Wet spaces
Elevator shaft walls

Exterior

External walls (*)
Roofs
Outdoor ceilings (*)
Soffit an fascia (*)
Fences and boundary walls
(*) for only prefabricated and light steel buildings.

Standard Dimensions

Thickness	08, 10, 12, 14, 16, 18, 20, 24, 26, 28, 30 mm
Dimensions	1250 x 2500 mm 1250 x 2800 mm 1250 x 3000 mm

Technical Specifications

Density	1300 ± 50 kg/m³
Thermal Conductivity Coefficient	0,15 W/mK (10°C dry)
Bending strength	>9 N/mm²
Modulus of elasticity	>4500 N/mm²
Fire resistance	B s1 d0 ( EN 13501-1)

Areas of Usage

Our panels are transported domestically and internationally with the plate edges painted and the Tepe Betopan® emblem.
The panels are on wood pallets covered in plastic with rings and corner brackets added.
During transport the panels must be covered in canvas.
When the panels are being carried one by one they are recommended to be carried vertically or as close as possible to vertical so as not to be bent.
The panels must be stored in a closed area.
Whether in storage or at the assembly site the panels must be left in lateral position and should not be leaned either laterally or vertically on a wall or similar surfaces.
If the panel packages are to be stacked caution should be taken to align them.
If the panels are not going to be used for a long period the packages should be completely covered in plastic to avoid being affected from heat and humidity change (stay stable).
After panels are taken from the package to be used the package should be covered over again with the plastic.
The storage area must be closed.
When stacking pallets the pallet feet should be lined up one on top of the other.
Do not take the plastic cover off until use.
Do not take off the steel strips until use.
The materials should be placed on the smoothest ground possible.
When storing, pallets should be carefully placed on top of each other with 5 pallets at most and the total height of pallets should not exceed 3,5 meters.
When loading, only two pallets at a time should be loaded.
When loading make sure that the pallets are placed on the truck in a balanced way.
Pallets ready for transpor

Help Center

Cement-Bonded Particle Board

Fiber Cement Board

Through Colored Fiber Cement Board

Pergola Awning Shutter Systems and Engines

Articulated Awning Engine®

Controls®

Advantages of Use

Areas of Application

Standard Dimensions

Thickness

Dimensions

Technical Specifications

Density

Thermal Conductivity Coefficient

Bending strength

Modulus of elasticity

Fire resistance

Areas of Usage

Newsletter Subscription